F4A41 / F4A51 / F5A51 / A5HF1
Downloads
| F4A41 (3.36 MB) | Download |
|---|
Part #
Reference #
Repair kits
Qty
OH Transfer Case F4A51 Santa Fe, Tucson
- Part #
- TSKF4A51
- Reference #
- Extra information
OH F4A41-1,F4A42-2 96-up Transtec
- Part #
- DP2323
- Reference #
- 41002A
- Extra information
- Transtec
OH F4A41-1,F4A42-2 96-up Precision
- Part #
- K77900R-MD
- Reference #
- 41002A
- Extra information
OH F4A51-2 Santa Fe/Trajet 97-09
- Part #
- K77900Q-MD
- Reference #
- 41002B
- Extra information
OH A5HF1 (F5A51) Hyundai, KIA Precision
- Part #
- K77900BB
- Reference #
- 41002H
- Extra information
Part #
Reference #
Filters
Qty
Filter F4A41/51/F5A51, A5HF1 metal/plast
- Part #
- 42710V
- Reference #
- 41010BA
- Extra information
- 4632139010
Filter F4A51/F5A51 / 41010C full plast
- Part #
- 42710U
- Reference #
- 41010C
- Extra information
Filter Extern F4A41,F4A42,F4A51(spin-on)
- Part #
- 42710T
- Reference #
- 41013A
- Extra information
Part #
Reference #
Valvebodies
Qty
Part #
Reference #
Valvebody Components / Transmission Specialties
Qty
Press.reg.v. F4A41, F4A51 (OS)
- Part #
- 41954-01K
- Reference #
- Extra information
Press.reg.v. F4A41, F4A51 (OS)
If wear in Mitsubishi F4A and F5A applications occurs at the balance/inboard end, the valve will not stroke to reduce line pressure and reduces feed to the converter/lube circuits. This can result in high line pressure, harsh shifts, reduced converter pressure and loss of lube. Severe wear at the other pressure regulator valve circuits can allow line pressure to exhaust, resulting in low line pressure, soft shifts and burnt clutches and bands. Sonnax oversized pressure regulator valve kit 41954-01K restores the valve body to normal operating condition.
- Valve is hardcoat anodized to reduce wear
NOTE: May be used in Mitsubishi front wheel drive, 96-later valve bodies including F4A41/42/51, F5A51 and Hyundai/Kia A5HF1 and A5GF1. However, OE valve spool diameters MUST be measured to verify application. This kit CANNOT be used in rear wheel or all wheel drive units.Required tool:F-41954-TL
Acc.piston F4A, F5A, V4A, V5A, R4A,R5A
- Part #
- 41954-02K
- Reference #
- Extra information
- Symptoms: Delayed engagement Harsh shifts Shudder on engagement Soft shifts Worn accumulator bores Cause: Side loading of the piston wears the piston bore. Correction: The Sonnax accumulator piston kit improves sealing and prevents future wear.
TCC cntrl valve F4A,F5A,V4A,V5A
- Part #
- 41954-03K
- Reference #
- Extra information
TCC Control Valve Kit
Part No. 41954-03KApplication units noted may look different than the two valve bodies pictured here. 41954-03K should fit all units with matching spool diameters, even if location of bore differs.
- Drop-in replacement part
- Valve is hardcoat anodized to reduce wear and features for proper centering and best hydraulic sealing integrity
- Highly wear-resistant alloy aluminum sleeve incorporates an O-ring to provide positive sealing against valuable line pressure leakage to exhaust.
- Critical valve spools are lengthened by almost 15%
- More than 80% more sealing contact area at the outboard line port area during TCC apply, while the critical outside diameter of the sleeve provides more than twice as much sealing capacity
- Valve
- Sleeve
- O-Ring
Press.cntrl.v.F4A,F5A,V4A,V5A A no orrif
- Part #
- 41954-06K
- Reference #
- Extra information
Pressure Control Valve Kit
Part No. 41954-06KNon-Orificed design
- Drop-in solution no special tools necessary!
- Hard-coat anodized aluminum valve and highly wear-resistant alloy aluminum sleeve resist wear
- Sleeve incorporates an o-ring to provide positive sealing against valuable solenoid feed pressure leakage to exhaust.
- Valve and sleeve have increased critical contact areas to provide better hydraulic sealing and increase stability and durability.
- Linear contact distance increased 46% at sleeve/valve interface during clutch apply
- Valve No Orifice
- Sleeve
- O-Ring
Press.cntrl.v.F4A,F5A,V4A,V5A B w/orri
- Part #
- 41954-07K
- Reference #
- Extra information
Pressure Control Valve Kit
Part No. 41954-07KWith orifice
- Drop-in solution no special tools necessary!
- Hard-coat anodized aluminum valve and highly wear-resistant alloy aluminum sleeve resist wear
- Sleeve incorporates an o-ring to provide positive sealing against valuable solenoid feed pressure leakage to exhaust.
- Valve and sleeve have increased critical contact areas to provide better hydraulic sealing and increase stability and durability.
- Linear contact distance increased 46% at sleeve/valve interface during clutch apply
- Valve With Orifice
- Sleeve
- O-Ring
Part #
Reference #
Frictions
Qty
Friction OD SS, id spl. A5HF1 (3) F5A51
- Part #
- 512117
- Reference #
- 41100
- Extra information
- Thickness: 0.099''/2.51mm. 30 Teeth. Outside diameter: 5.829"148.057mm.
Friction OD, SS, od spl. A5HF1 (3) F5A51
- Part #
- 512118
- Reference #
- 41100
- Extra information
Friction A5HF1 UD (3) V5A51 OD+UD
- Part #
- 512084
- Reference #
- 41100B
- Extra information
- Thickness: 0.070''/1.78mm. 30 Teeth. Outside diameter: 5.830"148.082mm.
Part #
Reference #
Steels
Qty
Part #
Reference #
Bands
Qty
Part #
Reference #
Bushings
Qty
Bushing Pump F4A41, F5A51, V5A51
- Part #
- 41005-01
- Reference #
- 41034E
- Extra information
- Pump Bushing Part No. 41005-01 Tooling: 41005-TL Sonnax offers replacement pump bushing 41005-01 for Mitsubishi F4A41/42/51, F5A51, R4/V4A51 and R5/V5A51 pumps. This precision steel-backed, ball-indented bushing restores operational clearances for proper sealing and lubrication. 41005-01 has a full bearing surface with no cut-out to compromise bearing integrity. Correct installation staking the bushing into the pump housing. This series of pumps are difficult to reassemble properly. There are no pins or mating features to ensure proper alignment of the pump halves. Sonnax offers pump alignment tool 41005-TL to correctly align the pump halves during reassembly. Allows salvage of pump Bushing is not available from OE Pump alignment tool properly aligns pump for assembly Specs Bushing Style: Precision Material: Steel-backed bimetal Shaft Dia.: 1.691" Width: 0.545" Housing Bore: 1.810"
Part #
Reference #
Seals
Qty
Cover Mitsubishi F4A41, F5M42
- Part #
- GC48-8.01
- Reference #
- Extra information
Diameter:
· Ø 48x8mm
Seal Pump F4A22/33/F4A41/51,V5A51 A4CF
- Part #
- 77601
- Reference #
- 142070A
- Extra information
- # 44-60-8,5
Part #
Reference #
Gaskets
Qty
Pangasket F4A51/F5A51/A5HF1 96-up
- Part #
- 77900LXD
- Reference #
- 41301B
- Extra information
Part #
Reference #
Washers & Bearings
Qty
Part #
Reference #
Electrical Components
Qty
Part #
Reference #
Hard Parts
Qty
Part #
Reference #
Tools
Qty
Pump-allign Tool F4A41,F4A51,F5A
- Part #
- 41005-TL
- Reference #
- Extra information
Pump-allign Tool F4A41,F4A51,F5A
Sonnax offers replacement pump bushing 41005-01 for Mitsubishi F4A41/42/51, F5A51, R4/V4A51 and R5/V5A51 pumps. Correct installation requires staking the bushing into the pump housing. This series of pumps are difficult to reassemble properly. There are no pins or mating features to ensure proper alignment of the pump halves. Sonnax pump alignment tool 41005-TL will correctly align the pump halves during reassembly.
Reamer press.reg.v. F4A51, F5A51
- Part #
- F-41954-TL
- Reference #
- Extra information
Tool Kit
Part No. F-41954-TL
- Reamer
- Reamer Jig
- Guide Pin
Note: Sonnax F-Tool kits require VB-FIX fixture
Tool Press.reg.v. A5HF1, A5GF1 (OS)
- Part #
- F-41954-TL15
- Reference #
- Extra information
Tool Press.reg.v. A5HF1, A5GF1 (OS)
- Reamer
- Reamer Jig
- Guide Pin
Tool Kit for 41954-15K
NOTE: Sonnax F-Tool kits designed to service a specific bore require the VB-FIX, a self-aligning valve body reaming fixture.
Part #
Reference #
Various
Qty
Part #
Reference #
Torque Converters
Qty